Office Chairs Made From Car Seats [Unique Ideas]

Usually, comfy office chairs may be unreasonably costly, and even the most costly ones deal more with aesthetics than with convenience every hour. When you’re on a budget, it’s uncomplicated, enjoyable to make an office chair from a car seat and a surplus pivoting bureau chair.

Given that the criteria for strength and precision are not all that significant, this is a perfect first unique project for novices in metalworking. Otherwise, make up the drill vehicle seat, the bit hacksaw, the tape measurement, wrench, the ratchet set pin). It can be painted to correspond to the other sections.

Can you turn a car seat into an office chair?

We employed scrap steel parts, but in your local shop, you can also get metal. We proceeded by cutting and boiling a piece of corner iron at any end of the sitting position. Then we cut 2 extra steel pieces to make a box. This box should preferably fit the base of the chair.


Why do you need to convert your car seat into an office chair?

In considerably higher standards, the office chair is made at lesser numbers and generally customized for customers that might purchase hundreds of thousands at a once. They also take a long time to be comfy and ergonomically designed behind them. So it is better to convert your car seat into an office chair than buy an office chair.

Please, purchase these tools from the link that is given below to convert your car seat into an office chair.

Tools you’ll need: Drill & bit hacksaw, measuring tape, wrench and ratchet set pliers.

Tools you’ll want: Center punch, chop saw, welder

Parts require: Angle iron, nuts & bolts, desk chair, car seat

How to Make an Office Chairs from Car Seats [6 steps]

You should follow these six steps to convert your car seat into an office chair

Step-1: View two option

Office jobs aren’t horrible, what about air conditioning and living wages. Yet there is one thing that bugged us: our awkward chair.

Most people view here 2 options: to have a restless perch the whole day or to pick up one of the pricey “executives” seats on the SkyMall list. However, we are automobile fanatics, therefore we choose a solution more innovative.

Almost anyone who has constructed a car or two has an additional seat, and it was the inventory of a Fiesta in our instance. It’s time to do it.

Step-2: Set the base

The chair of the office is secured on its platform by 4 bolts at the center, while the seat of the Fiesta falls on each side with a bolt. We’d have to create an adaptor to fasten the Fiesta seat to the bottom of the office chair

We utilized scrap material pieces and, you may also purchase some suitable metal from amazon. We began cutting, boiling, and fastening a piece of iron angle to each end. Then, to build a box, we cut two further steel pieces. This box should preferably match the base of the office chair.
We bolted all together and sat on the base of the chair, to ensure all was properly aligned.

Step-4: Check the seat

We bolted all together and sat on the base of the chair, to ensure all was properly aligned.

Step-5: See the steel performance

Time for the torch to come out and solder together all our steel components. Don’t you own a soldering machine? Bolting together all the metal will also work great. We boiled 4 gaps and bolted the metal to the base when the solds were cold. We were prepared to fit the car’s seat after applying an early layer of paint.

Step-6: Check the base

In order to ensure we placed the load over the base, we offered it a test set. Not unexpectedly, our new chair is considerably easier than that one it has replaced.

Watch this video to get more Ideas.

I am fond of making such good things that we can reuse in our day-to-day life. In this article, I am trying to share with you some unique Idea and that is how to turn Junker Car Seats Into Beautiful Office Chairs. So read this whole article to know this topic. so let’s start.


Step 1: Design and Parts Needed

Seeing various instances on the internet, some of them are quite eye-catching, pricey, but most appear too corny. I wanted me to seem really professional yet in an acceptable pricing range. Since I did anything like this before, I wasn’t sure how well it could come out. I proceeded, though. The parts I’ve used are below.

Things to need
  • Old Seats (Junkyard -40 box for both)
  • Foam (John Hancock Fabrics) (30 boxes)
  • Synthetic Leather Seat Covers (Took a big chunk but the quality was excellent) ($100 for each cover)
  • Lots and lots of Spray Adhesive (Loctite & 3M) (~10 boxes)
  • Silicone Caulking (Idea didn’t work) (10 boxes)
  • Spray Paint, Rust Remover, Associated Hardware (~20 boxes)

Step 2: Dis-Assembly

For the past 30 years or more, these seats have not been touched and misused. I saw this because there seems to be a bit of rust and no weight of the cushion when the chairs were apart. They have also utilized several cocoa liners, particularly on the top of the seat. The fastened screws were located on the chassis. It was a hassle to get them out of the house. I tried to get them out with a little smart leverage and body weight.

Step 3: Recovering Existing Foam

I examined numerous websites, with some saying that pure silicon spraying can restore its solidity. Hey, 10 box is worth trying. I was a bit doubtful. When this strategy didn’t work, I wasn’t shocked. To still be honest, the foam has become a bit tighter but I believe the silicone approach works if the foam is less than thirty years old than mine.

The foam also had this incredibly strange odour that even the caulking was not able to cover. I chose to say it and manufacture my own foam. So I chose.

Step 4: Top Cushion

Well, you are seeing me removing from the roof all the old coconut lining. I merely took one piece of parchment paper to produce new foam and drew it up and cut it. It wasn’t tough and hard. Recall the compressed foam, and make sure to 1/4″ to 1/2″ larger than the trace in the foam.

Step 5: Bottom Cushion

The lower part was complicated because the curvatures and thickening were various kinds. I cut the spray out into four sections as I did here. I’ve traced the new foam and cut it off with an electrical scissor. Then I attempted to settle the piece in order to get the right curve and thickness once I got the basic shape.

Later on, I discovered that the fresh foam cutout must not be an exact reproduction as long as the original is not too far away. The procedure was so accelerated.

With the bottom covers, I had a huge problem. After several days, I bonded the parts and ripped the seal apart. It occurred to me that 3M is definitely a better option when considering and reading people’s projects. I also finely adjusted the foam to cling to the touch surface.

During the “gluing” process, I also supplied a lot of pressure. Basically, the primary time to join two objects is if the glue on the surface is highly sticky, usually approximately 20 seconds after application.

I jammed these parts between a chair and a table to retain the strain at its greatest level. Therefore, it adhered rather nicely, after the adhesive dried. And agree, 3M was the best option, I think it certainly kept much better. I’d want to try but oh well I have a Gorilla Glue sprayer.

Step 6: Test Install

I installed the bottom coil once the adhesive had set. The top covers were finished and ready for use. The arrangement was lovely, far better than I anticipated. You can see them standing up against the wall looks fantastic.

Step 7: Office Chair Stands

For the seats, I required a stand. I discovered two ancient chairs in the workplace which were in bad shape, but the stand was in wonderful shape. You can see that cheap wooden upholstery tears away, and the chair lacked screws/nuts.

In order to associate to the framework of the seat and chair stand, I estimated the right size, cut, and boiled hole in a piece of plywood under the structure. I have also these plywood inserts which will simplify the installation.

Step 8: Cleaning and Painting

All the fittings, boults, and nuts I felt it necessary to clean. I grated all bearings again, and if required, placed the motor oil. It’s going to last for a long period of time and prolong the life of all bearing.

I also sprayed both plywood pieces and repaired the two-seat foundation. I removed the rust layer off the frame and placed a protective cap to prevent the development of any corrosion on the frame.

Step 9: Final Assembly

Having dried these components, it’s time to rally and hope all fit perfectly. I had a little issue with the brackets. Besides, It was difficult to maintain it and to synchronize the top of the seat. I finally got it. Tying together all the remaining bits and the viola fits all together, and all perform just as I had envisaged in my thoughts.

A final thought on How to Turn Junker Car Seats Into Beautiful Office Chairs

This assignment was undoubtedly very demanding and tough. I’ve never learned something that’s invaluable to me before. Whenever I can train myself in something new, this is pure knowledge and I’m going to absorb it every day. Last month I worked on this project, but it all valued it. I’m quite happy with myself. The links below to I find valuable resources.

FAQ on Chairs Made from Car Seats

In this section, I’m trying to share some questions and answers that can remove your confusion.

Are office chairs worth it?

Although they are pleasant to have, many little office changes also can greatly affect the comfort of your job from home. Regardless of the number of individuals who swear by fine office chairs, indebtedness or the extra money definitely shouldn’t be strained.

Are Car Seats good after the manufacture date?

Car seats often expire 6 to 10 years from the date of production. They expire for a multitude of reasons, involving wear and tear, restrictions, reminder, and manufacturer testing restrictions.

Can I use an expired car seat?

A speaker said, “No laws or restrictions on the use of an expired date car seat are now in force in the United States.” The US administration is unaware of the likelihood of a kid safety seat degrading over time.


Hey! this is an extraordinary and unique article for you to convert your car seat into an office chair. Hopefully, you are able to know about this topic in-depth information with a video. Further, if you have any confusion or question, you can ask me in the comment section and I’ll try to solve your question.

At the heart of is our visionary Head Content Creator, Mr. Russell Leyva. With a profound love for cars and an unparalleled enthusiasm for the automotive industry, Russell brings a unique perspective to the world of automotive blogging.